华为CE6800系列iStack配置
1.执行命令system-view,进入系统视图。
2.执行命令stack,进入堆叠管理视图。
3.执行命令stack member member-id renumber new-member-id ,配置堆叠成员设备的堆叠成员ID。
缺省情况下,设备的堆叠成员ID为1。配置了堆叠成员ID后,需要重新启动设备配置才能生效。
Execute system-view, enter the system view.
2. Execute the stack, enter the stack management view.
3. Execute the stack member-id remember new-member-id.
a.执行命令interface interface-type interface-number,进入接口视图。
b.执行命令shutdown,关闭当前接口。
c.执行命令quit,退出接口视图。
d.执行命令commit,提交配置。
A. Execute command interface interface-type interface-number, enter the interface view.
b. Execute command shutdown, close the current interface.
c. Execute command quit, exit the interface view.
d. Execute commandcommittee, submit configuration.
a.执行命令interface stack-port member-id/port-id,进入堆叠端口视图。
b.执行命令port member-group interface interface-type { interface-number1 [ to interface-number2 ] } &<1-32>,向堆叠端口中添加成员端口。
c.执行命令quit,退出堆叠端口视图。
d.执行命令commit,提交配置。
An executive command interface block-port member-id/port-id, entering the stacking port view.
b. Execute command member-group interface interface {interface-type1 [to interface-number2]]} & < 1-32> add a member port to the stacking port.
c. Execute command quit, exits the stacking port view.
d. Execute commandcommittee, submit configuration.
1.CE6810_A重启
2.CE6810_B重启
3.连接线缆后,CE6810_B优先级低,会重启,重启后加入堆叠成员
CE6810_A restarted
2. CE6810_B restarted >br>3. CE6810_B low priority will restart and then add stacking members.
通过配置堆叠双主检测,可以检测并处理堆叠分裂时网络中出现的双主冲突,有两种方式
1.配置业务口直连方式双主检测
如果堆叠系统的成员交换机上有闲置的业务端口,可以采用业务口直连方式的双主检测。业务口直连检测方式需要额外占用端口,且此端口只能用作双主检测。
2.配置Eth-Trunk口代理方式双主检测
如果堆叠系统上配置了跨设备Eth-Trunk,此时可以采用代理方式的双主检测。Eth-Trunk口代理方式双主检测需要在堆叠系统跨设备Eth-Trunk上启用代理方式双主检测功能,并在代理设备上启用代理功能。
与业务口直连方式比较,Eth-Trunk口代理方式不会额外占用端口,也不会影响Eth-Trunk口正常业务报文的转发。
By collating the two main tests, it is possible to detect and process the two main conflicts that occur in the network when the stacking splits, and there are two mains in
1. There are two ways to configure the business interface.
> If there are idle business ports in the member exchange of the stacking system, it is possible to use two mains in the business interface. The business collide detectors require extra access to the port, and this port can only be used as a double main test.
2. Configure the Eth-Trunk proxy for
if the cross-equipment Eth-Trunk is configured on the stacking system, and the Eth-Trunk proxy will not take extra advantage of the port or affect the transmission of normal business from Eth-Trunk.
compared with the agent link to the business interface, the Eth-Trunk proxy method will not affect the normal business from the Eth-Trunk interface.
a.执行命令system-view,进入系统视图。
b.执行命令interface interface-type interface-number,进入接口视图。
c.执行命令dual-active detect mode direct,配置业务口的直连双主检测功能。(缺省情况下,业务口的直连双主检测功能处于关闭状态.)
d.执行命令commit,提交配置。
a. Execute command system-view, enter the system view.
b. Execute command interface interface-type interface-number, enter the interface view.
c. Execute command dual-active detetect mode direct, configures the direct dual master detection function of the operations. (In default, the direct dual master detection function of the operations is closed.)
d. Execute commandcommittee, submit configuration.
?在堆叠系统上
a.执行命令system-view,进入系统视图。
b.执行命令interface eth-trunk trunk-id,进入Eth-Trunk接口视图。
c.执行命令dual-active detect mode relay,配置Eth-Trunk接口的代理双主检测功能。(缺省情况下,Eth-Trunk接口没有配置代理双主检测功能。)
d.执行命令commit,提交配置。
? on a stacking system
a. Executing command system-view, entering the system view.
b. Executing command interface eth-trunk trunk-id, entering the Eth-Trunk interface view.
c. Executing command dual-active detectetmode relay, configures proxy double master detection features for the Eth-Trunk interface. (In default, the Eth-Trunk interface does not configure proxy dual master detection functions.)
d. Executing commandcommittee, submit configuration.
?在代理设备上
a.执行命令system-view,进入系统视图。
b.执行命令interface eth-trunk trunk-id,进入Eth-Trunk接口视图。
c.执行命令dual-active proxy,在Eth-Trunk接口上启用代理功能。(缺省情况下,Eth-Trunk接口未配置代理功能。)
d.执行命令commit,提交配置。
a. Execute command system-view, enter the system view.
b. Execute command interface eth-trunk trunk-id, enter the Eth-Trunk interface view.
c. Execute command dual-active protocol, enable proxy on the Eth-Trunk interface. (In default, the Eth-Trunk interface is not configured for proxy functions.)
d. Execute commandcommittee, submit configuration.
注册有任何问题请添加 微信:MVIP619 拉你进入群
打开微信扫一扫
添加客服
进入交流群
1.本站遵循行业规范,任何转载的稿件都会明确标注作者和来源;2.本站的原创文章,请转载时务必注明文章作者和来源,不尊重原创的行为我们将追究责任;3.作者投稿可能会经我们编辑修改或补充。